oshitwaddup

joined 1 year ago
sorted by: new top controversial old
Jerboa 0.0.55-alpha Release in c/[email protected]
[–] [email protected] 3 points 10 months ago (2 children)

Newpipe has it's own fdroid repo, maybe jerboa could do that too?

Shit story in c/[email protected]
[–] [email protected] 2 points 10 months ago

Absolutely

*Permanently Deleted* in c/[email protected]
[–] [email protected] 7 points 10 months ago (16 children)

Probably just go extinct very quick

Anon goes on a date in c/[email protected]
[–] [email protected] 7 points 10 months ago

Eh, some people don't want to be asked, but also, if they can't handle being asked (especially for the first kiss. Later kisses rarely need to be so explicit) then you're probably dodging a bullet anyways.

Shit story in c/[email protected]
[–] [email protected] 18 points 10 months ago (2 children)

another banger from crackermilk (check them out on youtube)

I got better reasons buddy in c/[email protected]
[–] [email protected] 23 points 10 months ago

Boy-pussy, butt-pussy, back-pussy. There are many paths to the top of the mounain.

Anon goes on a date in c/[email protected]
[–] [email protected] 12 points 10 months ago (6 children)

Lots of caveats to this so don't just blindly go around asking people for a kiss or whatever, but for a date, especially the second half or end of the date, I think a good rule of thumb is to assume they want the kiss/hand hold/etc, BUT the critically important thing is you should just ask first and respect whatever answer they give. "Can I hold your hand?", "Do you want to kiss?", etc. If the women in your story and ops had done that, they almost certainly would've gotten what they wanted, but often people expect men to be the one to initiate, and no matter what gender you are it's scary to do anyways.

kbin instance running on green energy? in c/[email protected]
[–] [email protected] 3 points 10 months ago

Yep, the lemmy devs seem to actively want lemmy to not have that functionality 😔

*Permanently Deleted* in c/[email protected]
[–] [email protected] 2 points 10 months ago

Proactively seek out relevant info, proactively update based on new information, and murphy-jutsu/pre-hindsight (imagine the situation has failed horribly. What went wrong?), to name a few things that help

32
kbin instance running on green energy? (fedidb.org)
 

I'd like to be able to follow users and communities so I'm looking to switch to kbin. Are there any instances that use green energy?

20
Rule (slrpnk.net)
 

[email protected] trying to open this community in jerboa

Proton desktop app in beta in c/[email protected]
[–] [email protected] 3 points 10 months ago

Yep, and mullvad vpn has been great on linux, plus they support ipv6 which imo should also be basic/minimum functionality for a modern vpn service

Pizza Rule in c/[email protected]
[–] [email protected] 8 points 10 months ago

Ah but it's mini-nutrition now, so you have to shrink yourself in order for your body to be able to process it

Proton desktop app in beta in c/[email protected]
[–] [email protected] 1 points 10 months ago (2 children)

Same. Terrible linux support for their vpn (on top of all the obvious issues it has, it also requires networkmanager which I don't use, and iirc doesn't support ipv6) drove me away, tuta has been much better imo. Especially since tuta on android doesn't depend on google play services (proton mail does), which should be basic functionality for a privacy focused service

22
Best foss budget software for both linux and android? (lemmy.antemeridiem.xyz)
submitted 11 months ago* (last edited 11 months ago) by [email protected] to c/[email protected]
11 comments fedilink
 

Looking to start budgeting, I'd like to be able to use it on both android and linux and use syncthing to sync the file. Is there a good solution for that?

it'd be nice if I could easily divide my income into different buckets, add expenses to those buckets, and see how much is remaining in any given bucket for the current month. Less important but still nice would be an easy way to roll surplus into the same bucket for the next month

27
Add jerboa to accrescent? (accrescent.app)
 

I recently became aware of the Accrescent app store after reading this article: https://privsec.dev/posts/android/f-droid-security-issues/. It's still in alpha, so it might make sense to wait for it to mature before adding jerboa, but I think it'd be good to have jerboa on there eventually

-5
always good to hear abolitionist discussions. The one thing he's missing is the full john brown spirit towards injustice (www.youtube.com)
-2
his message at the end about why he keeps going is solid, it's about getting up and doing the right thing every day. It's good to see people who care using their voice like this (www.youtube.com)
21
Firefox still doesn't have PWA support (connect.mozilla.org)
 

I really wish there was more word from mozilla on this. There are a few electron apps that I'd much rather use a PWA for so I can totally ditch chromium/electron

24
What's a good federated social media that's less anonymous/more like facebook? (lemmy.antemeridiem.xyz)
 

I'm looking for something where I can do some local community building, I'm guessing mastodon might work but I think the ideal is something like facebook where I can join a group tied to a common idea and a location, as well as being a bit more personal. Is there anything like that?

16
Any ideas on what to change to fix my prints? (postimg.cc)
 

cross-posted from: https://lemmy.antemeridiem.xyz/post/123877

The main thing I'm not sure about is the gaps on top and the globs and strings on the top and sides. I think the gaps on the bottom might be needing to level the bed and extruders better, and maybe I need to try a raft for the warping?

I'm using a flashforge creator pro with a glass print bed and layerneer bed weld, happy to fill in any other details too. I'm new to 3d printing so I'm not really sure what all the necessary details might be needed to figure out the problem

13
Any ideas on what to change to fix my prints? (postimg.cc)
 

The main thing I'm not sure about is the gaps on top and the globs and strings on the top and sides. I think the gaps on the bottom might be needing to level the bed and extruders better, and maybe I need to try a raft for the warping?

I'm using a flashforge creator pro with a glass print bed and layerneer bed weld, happy to fill in any other details too. I'm new to 3d printing so I'm not really sure what all the necessary details might be needed to figure out the problem

3
Should we try to use a different service for uploading images, or is it ok to use the native uploader? (lemmy.antemeridiem.xyz)
submitted 1 year ago* (last edited 1 year ago) by [email protected] to c/[email protected]
2 comments fedilink
 

Idk if it would make a significant difference or not, but i know i post memes occasionally and i realized i might be causing excess strain on your server, so i wanted to see if you had any thoughts

1
rule (lemmy.antemeridiem.xyz)
 
view more: next ›