thegreekgeek

Hey all!

I posted this to /c/tailscale yesterday and I figured I'd post it here to get some more visibility.

I'm trying to ssh into my tailnet-hosted (through tailscale serve) gogs instance and I can't seem to figure out how. Has anyone tried doing this? Will I need to add a user to the sidecar container and add a shim like they do in the regular gogs setup? I appreciate any insight.

Edit: Added tag and modified title for clarity.

Hey all!

I'm trying to ssh into my tailnet-hosted (through tailscale serve) gogs instance and I can't seem to figure out how. Has anyone tried doing this? Will I need to add a user to the sidecar container and add a shim like they do in the regular gogs setup? I appreciate any insight.

Edit: Modified title for clarity

Hey all, just ran into this this morning, I was replying to a comment and it showed up at the same level as the comment I was replying to until a refresh. I'll see if I can reproduce it for screenshots in a bit. Has anyone else noticed this or is it just me so far?

Like it says in the title, just woke up to a thunderstorm and saw this when i took a peek outside.

It happened recently, the share function doesn't seem to be pulling the URL from the page.

Edit: this is with Firefox mobile beta 127.0b9 as my default browser

Hey all! I've been chewing on this problem for a bit and I've hit a wall, I'm hoping someone here can point me in the right direction.

I have an auto entities card populating a series of mushroom chips on the top of my dashboard for stuff like lights on, available updates, and open doors.

The thing is, some of the doors that have sensors on them are open by default, and as a result the chips are there all the time.

Ideally I'd like to have seperate auto entities entries for each group, default open and default closed, but I'd like to keep them in the same card as everything else(they're sorted by time triggered); and I can't for the life of me figure out how to filter out specific entities from a single entry in the include filter. I can exclude something from the whole card, but I haven't found anything that would allow me to just show certain closed doors or certain open ones.

Hopefully this made sense! I appreciate any ideas you have.

EDIT: So I finally got it figured out without futzing with my setup too much, sorry @borebore, I didn't end up going with the template sensor. I ended up finding a python script that allows you to inject custom attributes, so I made an automation that anytime the "normally closed" doors updated their status it'd give them an "is_normally_open: true" attribute and filtered the auto entities chips off of that attribute.

Thanks everyone!

My first time encountering it, just scrolled to it like three times to check, anyone else having this issue?

Edit: ope, looks like I can't edit the title lol.

Hey all! I was looking for an Android Auto replacement app recently and came across Zenroad there's also an android build but it's not compatible with my device unfortunately. Has anyone had any experience with this app?

Edit: ope, just saw the sidebar. Apologies!

Hey all, I just finished a run of Popandsicle's excellent vase mode ornaments and I noticed these weird bulges happening all over the prints. The last run in a different color was flawless so I'm not sure where to start. I couldn't find much on the issue with a bit of googling so I thought I'd check with you folks and see if you all had any insight.

I've calibrated my esteps and adjusted the resolution to be a bit easier on my printer (modified CR-10v2), and unfortunately my mainboard isn't capable of linear advance.

Filament is overture royal gold, layer width is 0.6, height is 0.2.

I appreciate the help!

To be clear I know it's not well lol. I just wanted the community's thoughts on what I'm doing wrong. I'm using Overture Royal Gold on a modified CR-10v2 with a real V6. Model was sliced in cura with default low quality settings.

The filament I bought a few months ago but just broke it open yesterday. It's making some small popping noises every now and again but the seal didn't appear to be broken. It seems all right otherwise, if a little sticky on the roll. I had to move it out of my filament dryer to keep it from opening the lid because it was binding so much. That's what happened to the last tower, that failed mid print. Looks nice at least.