In addition to what the other guy said, email elegoo support, they have a good warentee system in place. They'll send you free replacement parts
this post was submitted on 16 Jul 2023
6 points (100.0% liked)
3DPrinting
15505 readers
169 users here now
3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.
The r/functionalprint community is now located at: [email protected] or [email protected]
There are CAD communities available at: [email protected] or [email protected]
Rules
-
No bigotry - including racism, sexism, ableism, homophobia, transphobia, or xenophobia. Code of Conduct.
-
Be respectful, especially when disagreeing. Everyone should feel welcome here.
-
No porn (NSFW prints are acceptable but must be marked NSFW)
-
No Ads / Spamming / Guerrilla Marketing
-
Do not create links to reddit
-
If you see an issue please flag it
-
No guns
-
No injury gore posts
If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is 
Moderation policy: Light, mostly invisible
founded 1 year ago
MODERATORS
I did send an email for support on Friday, I’m awaiting for they answer but I already disassemble everything on the extruder so I’m a little suspicious if the warrant will work.
But will wait to see if will works
I've done some horrific things to my printers and they didn't care. They are on aisian time (+7 or something UTC) so unless you near then, mostly likely the to and fro will be per day, so try and put as much info as possible into your messages if they get back to you for more info
Oh that’s great to know.
I did send a video and a couple of informations, I will wait for their answer and do what you said, send all the informations I can.
Thank you for helps me with that
Not worth to repair since they are cheap imo, but dont buy a motor before you confirm its not something else. You have 3 components, motor, wire and stepper motor. Plug it in x driver and move your x. If the problem is still there its motor or cable. Then switch cables if they are detachable, or visually inspect cable/connector. So if you are looking for feplacement, just find a label on your motor and search that on internet. If you dont chose the same model you might need to change your stepps/mm in fw or adjust current (vref). Its most likely nema17 bipolar 1.8 deg, but you have to check length to be sure it fits where your extruder should be. Simmilar size = simmilar power, but you shoudl fine tune your vref anyway. Too much current = motor overheating or stepper motor overheating and it can also skip, too low current = motor skipping. If it died you might be running it too hot, but you would probably burn driver first.
First of all thank you for your answer.
I will try to test it with the x axis I don’t know that will work.
I try to put a led and it light up ok on both poles.
I did search using the number on the motor, but I wasn’t able to find the exact model.
So can I just buy a similar size and wires and fine tuning in the firmware if anything goes wrong ?
The bill of material just says 42HD1418-01,Two-phase,25mm.
So any nema with 25 mm and 4 wires will work ?
Sorry for the lots of questions, but I’m a little lost in this replacement.
Ye I couldn't find any datasheet of that one. Maybe e-mail them and ask?
Well, I'd say any Nema17 bipolar (4 wires) 25 mm in length (similar current) and probably 1.8°/step or 200 steps/revolution (like most of them) should work. If you get wrong resolution (steps/revolution) your extruder will move wrong distance (like double), but you can change that in FW. And you should fine tune Vref (small screw on your stepper driver or in FW) to find sweet spot between heating and torque
You can do some math to identify resolution. Check your FW, quick search got me:
* Default Axis Steps Per Unit (linear=steps/mm, rotational=steps/°)
* Override with M92
* X, Y, Z [, I [, J [, K...]]], E0 [, E1[, E2...]]
*/
#if NEPTUNE_3_PRO
#define DEFAULT_AXIS_STEPS_PER_UNIT {80.00, 80.00, 400.00, 380.00}
#elif NEPTUNE_3_PLUS
#define DEFAULT_AXIS_STEPS_PER_UNIT {80.00, 80.00, 400.00, 390.00}
#elif NEPTUNE_3_MAX
#define DEFAULT_AXIS_STEPS_PER_UNIT {80.20, 80.20, 400.00, 390.00}
#endif
I guess its 380 steps/mm, but I should go deeper in that and do some math (gear teeth numbers, grub screw diameter) to confirm what resolution is original. Shouldnt be hard if you get all information needed, but still easier to ask them what stepper is that. Since its kinda standard 200 steps/rev would be my bet