this post was submitted on 05 Jul 2023
0 points (NaN% liked)

3DPrinting

15580 readers
220 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: [email protected] or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
[email protected]
[email protected]
[email protected]
[email protected]
0
Getting into 3d printing - printer advice (lemmy.world)
submitted 1 year ago by [email protected] to c/[email protected]
6 comments fedilink hide all child comments
 

Hello 3dpronting!

I am looking to get a resin printer as I have been reading they are better for smaller high detail prints. I am mainly looking to print miniatures for tabletop gaming.

I have been eyeing the Elegoo Mars 3 pro and the corresponding washing/curing station(Elegoo mercury plus 2 in 1).

Is this a good starting point? Am I biting off too much for a beginner?

top 6 comments
sorted by: hot top controversial new old
[–] [email protected] 0 points 1 year ago* (last edited 1 year ago) (1 children)

This is where I started with my resin 3d printing. I have an FDM as well and the the resin printer blows it out of the water in terms of detail and speed.

Small tip I've learned about the washing/cure station is to let your prints dry after taking them out of the wash before placing them on the curing station. This will prevent resin from curing on the platform and making a mess.

Know that you will need a lot more than just the printer and washing station though. You want gloves (by the box), 91%+ alcohol (by the gallon), some silicon mats to work on, microfiber towels (to clean your FEP), and lots and lots of paper towels. If you are concerned about fumes you'll want to look into ventilation. I guess what I'm saying is it's messy! It's not hard though and the models you get are amazing, my gaming group loves me and my GM is living out his childhood gaming dreams.

[–] [email protected] 0 points 1 year ago (1 children)

This is great thanks for the info! I didn't realize the alcohol has to be such a high %. Do you find it expensive to have to have that much high % alcohol on hand?

How often do you need to replace it? (Every print? Every other print?)

[–] [email protected] 1 points 1 year ago

I've been using my resin printer for about a year and I've only had to swap my alcohol once, but it can also be cleaned fairly easily with pure alum powder.

I personally use ethanol rather than isopropyl because a friend of mine is allergic to isopropyl, and it works just fine. The fumes are also less harmful from ethanol.

Still wear a respirator when using it though.

[–] [email protected] 0 points 1 year ago (1 children)

I started my foray into 3d printing with resin, too. It's a steeper learning curve; it feels like I've broken and repaired everything on my Anycubic Photon 4k at least once, and I've slowly collected every slicer program there is (settled on Lychee slicer Pro), but I don't have any regrets.

Just make sure you have the space for it. Ideally you want a non-carpeted room with ventilation and temperature control. Doesn't need to be big.

[–] [email protected] 0 points 1 year ago (1 children)

This is good to hear that youve had a relatively good experience. Did you have to replace things due to your own inexperience or just because you used it so much?

I was planning on just doing it in my garage with the garage door open and a fan blowing out. I think this would be enough vetilation of ventilation?

[–] [email protected] 1 points 1 year ago

Definitely inexperience in my case. I punctured countless FEP sheets due to print failures (caused by poor supports). Replaced the LCD once. But, my workload has greatly improved!

Garage would work, only concerns are managing the temperature and keeping dust/debris away from the work area. Lots of people successfully print from their garage!