this post was submitted on 04 Aug 2023
11 points (92.3% liked)

3DPrinting

15580 readers
220 users here now

3DPrinting is a place where makers of all skill levels and walks of life can learn about and discuss 3D printing and development of 3D printed parts and devices.

The r/functionalprint community is now located at: [email protected] or [email protected]

There are CAD communities available at: [email protected] or [email protected]

Rules

If you need an easy way to host pictures, https://catbox.moe may be an option. Be ethical about what you post and donate if you are able or use this a lot. It is just an individual hosting content, not a company. The image embedding syntax for Lemmy is ![](URL)

Moderation policy: Light, mostly invisible

founded 1 year ago
MODERATORS
 

Is this beyond the pale? Recently got a Neptune 3 pro and have been having issues. Anyone have some tips? Is this resolvable? Can a bed for these be replaced?

I uncommented the Gcode line to use this matrix now which I didn't before. But still having a lot on inconsistencies.

you are viewing a single comment's thread
view the rest of the comments
[–] [email protected] 2 points 1 year ago (1 children)

Gonna preface with saying I don’t have a Neptune… so this is from checking out photos.

First thing to check is how square the printer frame is- especially how the gantry is to the rest of the printer.

If you can, take a big triangle square to do that. You might have to loosen and retighten things, in that case go slow and tweak them all one bit at a time. You might also not ever be able to get it perfect. (I assume there’s a t-brace going between the gantry uprights and base. Hopefully it’s not just but-end bolts…)

from there check squareness if the x-gantry itself. That may be out of level and need adjustment.

Doubt that would solve a 3mm differential though.

Next it looks like there’s stand off pegs? You can take the tall pegs off and sand them down a bit until they match the low side. Tedious and annoying, and very easy to go too far. Before that try tightening the high side.

Maybe check them with a micrometer but ultimately every pass or two you’ll have to put them back in- it’s the carriage+posts+plate/bed altogether that’s out of whack.

And this is why I dislike rigid legs like this. Yes springs go out of level routinely, but the pegs will eventually go out of level all the same and it’s a PITA. Or you change some configuration and have to do it again…

Regardless, you should be able to set fade height to compensate for it. With say 10mm of f-height, the firmware will automatically adjust layer height until it’s square and flat at 10mm. If it’s absolutely critical for dimensions or appearance, you can set a 10.4mm raft.

[–] [email protected] 2 points 1 year ago (1 children)

It has pegs but I was able to see that there are rather typical screw heads in the heating plate to hold it down onto the bed's support frame, and if you look you can see the bolt ends coming down out of the underside of the supporting arms.

So I think what's here is pretty simple: regular bolts with fixed length spacer tubes around them.

And that means that OP should be able to sort this out with, say, the right collection of 0.5mm-thick washers. One on the front left screw, three on the right rear screw, uh, six on the back left screw should get close enough for the mesh to handle the remaining difference.

[–] [email protected] 1 points 1 year ago (1 children)

Are you referring to the screws underneath the build plate? Or do you mean the bolts to the frame? I've never had to go this far to level a bed so want to make sure I'm doing this right

[–] [email protected] 1 points 1 year ago (1 children)

Yeah, under the build plate there are four bolts pointing down. Those bolts.

[–] [email protected] 1 points 1 year ago

Thanks for the tip. I'll give this a go and see where I can get it!