Steam Deck

14810 readers

50 users here now

A place to discuss and support all things Steam Deck.

Replacement for r/steamdeck_linux.

As Lemmy doesn't have flairs yet, you can use these prefixes to indicate what type of post you have made, eg:
[Flair] My post title

The following is a list of suggested flairs:
[Discussion] - General discussion.
[Help] - A request for help or support.
[News] - News about the deck.
[PSA] - Sharing important information.
[Game] - News / info about a game on the deck.
[Update] - An update to a previous post.
[Meta] - Discussion about this community.

Some more Steam Deck specific flairs:
[Boot Screen] - Custom boot screens/videos.
[Selling] - If you are selling your deck.

These are not enforced, but they are encouraged.

Rules:

Follow the rules of Sopuli
Posts must be related to the Steam Deck in an obvious way.
No piracy, there are other communities for that.
Discussion of emulators are allowed, but no discussion on how to illegally acquire ROMs.
This is a place of civil discussion, no trolling.
Have fun.

Link to our Matrix Space

founded 3 years ago

MODERATORS

[email protected]

Screw stripped (discuss.tchncs.de)

submitted 1 year ago by [email protected] to c/[email protected]

9 comments fedilink hide all child comments

while upgrading the inner bottom left screw stripped...and nothing helped rubberband, superglue, nothing. Fkin hell a single screw is screwing with my plans

top 9 comments

sorted by: hot top controversial new old

[–] [email protected] 7 points 1 year ago

Superglue will work. You just have to do it right. Take a bit of iso alcohol and an old toothbrush and clean the screw off. Take a bit of fine sandpaper and scuff up the screwdriver bit and then clean it with iso as well.

Then add a tiny bit of glue to the driver and a tiny bit to the screw. Then wait 1 minute, push the bit into the screw down hard, and leave it be for 30 minutes before turning.

This is much easier to leave balanced for that 30 minutes if you have just a bit and not the whole screwdriver to leave balanced.

[–] [email protected] 5 points 1 year ago (1 children)

How did you apply the super glue?

This is difficult since obviously you don't want to apply too much pressure on delicate electronics, but I have dealt with many strips, screws in cabinets and have a pretty good success rate, although one time using super glue, I just used a sacrificial crappy screwdriver, and had to end up holding the screwdriver to the screw with pressure. Applying super glue, and holding the sacrificial screwdriver with pressure for 10 minutes until I was sure it had bonded, but with such small margins of screw to a back plate and such a thin screwdriver, I'm not sure that will work with your deck.

If you have any access to the screw at all and play between the back plate and the casing, there are very thin hacksaw blades you could buy from a home improvement store and you could manually cut through the top of the screw and then use needle nose pliers to unscrew the bottom of the screw from its setting, since you should have some threads sticking out of the setting.

Can you throw up a couple pictures?

Best of luck, I hope my explanations are in vain and you've already solved it.

[–] [email protected] 2 points 1 year ago (1 children)

Superglue becomes brittle when frozen. Instead of sacrificing a screwdriver, you could try freezing the screwdriver and maybe you could snap the superglue off afterward

[–] [email protected] 2 points 1 year ago

Oh, I just used sandpaper for a very long time haha, but that's good to know about it being brittle when frozen.

Thank you. I will keep that in mind next time.

[–] [email protected] 3 points 1 year ago (1 children)

Try cutting a slot in the top of the screw. I use a small rotary tool with a cutoff wheel at low speeds, but a hand file would work too. Then you can use a normal slotted screwdriver with the screw.

[–] [email protected] -1 points 1 year ago (1 children)

The screw threads are stripped, not the top.

[–] [email protected] 5 points 1 year ago

Opening up a plastic shell? Doubtful.

[–] [email protected] 3 points 1 year ago

I know iFixit sells screw extractor bits that apparently work well, though I haven't tried them myself: https://www.ifixit.com/products/precision-screw-extractor-set Might be with checking out these or something similar

[–] [email protected] 2 points 1 year ago

Hah, screwed your plan 😅