this post was submitted on 08 Aug 2023
210 points (98.2% liked)

Home Improvement

9011 readers
59 users here now

Home Improvement

founded 1 year ago
MODERATORS
 
you are viewing a single comment's thread
view the rest of the comments
[–] [email protected] 12 points 1 year ago* (last edited 1 year ago) (2 children)

No expansion tank?

Guessing its a hybrid unit? I have a hybrid one by GE. Goddamn its loud.

Don't forget to turn up the water temperature. Mine also was set to 120 by default, but that's too cold. You need 135-140 or so, otherwise you'll find that you run out of hot water pretty quickly, especially if you have people taking showers back to back, or running the dishwasher/washer while someones showering, etc.

[–] [email protected] 10 points 1 year ago* (last edited 1 year ago) (2 children)

What's an expansion tank? I set it up like the old one was set up. All I did was disconnect the old one and reconnect the new one to the same pipes coming out of the wall.

[–] [email protected] 5 points 1 year ago* (last edited 1 year ago) (4 children)

An expansion tank is necessary for water heaters, because the process of heating water causes it to expand. Without an expansion tank, pressure could build to unsafe levels

[–] [email protected] 17 points 1 year ago

All tanks are equipped with a safety release for the pressure and the only time when that delta in pressure can be problematic is when you go from completely cold to hot due to the higher amount of water that can fit in the tank at lower temp.

Otherwise I've never seen a house in Canada with an extension tank attached to the water heater and the water come in ice cold in the winter.

[–] [email protected] 11 points 1 year ago (1 children)

Pressure won't build up, it will be let out by the pressure relief valve and make a mess on the floor. Which is also undesirable.

[–] [email protected] 1 points 1 year ago

Well, right up until the pressure relief valve fails. Whether it fails open or closed, you're gonna have a bad time, because either way you're probably going to have a lot of water where there's not supposed to be water.

[–] [email protected] 3 points 1 year ago* (last edited 1 year ago)

In reading it looks like it is for homes newer than 1986? Our old water heater was 20 years old and we never had any issues with the pressure getting too high.

[–] [email protected] 3 points 1 year ago (3 children)

If it's necessary then how did my last tank make it 20 years without one?

[–] [email protected] 3 points 1 year ago

If you are on municipal water and there is no check valve between you and the water meter then the municipal water supply is acting as the expansion tank. It may not be to code in your area but that's how many homes were built in the past.

[–] [email protected] 1 points 1 week ago

The expansion tank isn't just for the water heater. That increased pressure puts undue strain on the entire plumbing system in your home. It will cause toilet fill valves to fail, supply lines to rupture, and possibly even pinhole leaks. A lot of plumbing issues are solved by installing an expansion tank.

[–] [email protected] 1 points 1 year ago (1 children)

Honestly, I don't know, I'm not a plumber. There are a couple possibilities, including that it was built into the water heater or the relief valve did it's thing. Some water heaters don't need expansion tanks at all, either. It's generally a "just in case" thing, since the right failures in the wrong way could lead to a hot water bomb going off in your house.

[–] [email protected] 1 points 1 year ago

Yeah but that was like the coolest mythbusters episode ever /s

[–] [email protected] 1 points 1 year ago

Another comment here says the lower element of this unit has a flaw. Might look into that.