Why is that?
UnH1ng3d
joined 10 months ago
Can you give some examples ๐
I've read the "learn more" bit now and I'm going to leave it switched on. (although I use uBlock anyway โ๐ )
I think this is a legitimate attempt to 'fix' the internet. It seems only very basic information on interactions with ads is recorded by the browser, and then it is anonymised. As an example, the advertiser should only receive counts of how many people bought a product after seeing a particular ad. I don't think they can see what webpage anyone in particular came from, but maybe they can see that: 11% percentage of visitors came from example.com/some-page
Presumably the anonymised data is only provided once the pool is fairly large and wouldn't show 100% of visitors came from cornhub when you only had one visitor ๐คทโโ๏ธ Obviously websites will always see an IP address.
The idea is for this to substitute for traditional, more invasive, tracking. I think it may one day achieve that.
A warning though: I only just started reading about this.
Excuse me while I go and click that 'learn more' button...
I've had the same thing. I think orca's retraction test is just too 'easy'. I think the towers are too far apart.
I can see a bit about the solid state relay overheating with too much power, but that's not the bed. Have I missed something or have you possibly misread something yourself ๐คช
I don't know how small you are thinking, but if it's V0 size, make sure you've seen the "crucible" on 3dprintersforants, it looks cool ๐
I don't think anyone has a v0.2 in this instance ๐ Thanks for going out of your way to answer my question, even though you can't ๐คฃ
I'm wanting it because I realise I do a lot of very small parts and I often want to iterate on them quickly, so a fast bed heat would be quite nice. I currently always heat soak for bed meshes and such, but I haven't found it necessary for prints - they're usually not that big though ๐คทโโ๏ธ
Do you know where I can find that documentation on max heating?
Thank you ๐
That's extremely helpful, and I didn't even expect a reply after this time.
How many watts is the heater you are using?
I'm thinking of buying a used 0.2 and I wondered if it might be fun to change to an AC bed. I read the original v0 had one but some kits were using improper solid state relays so they changed it for safety ๐ง
I certainly see you the chamber heat argument for ABS ๐ช
Why do bed slingers heat faster?
You can't trust what you can't see.
When I do an overhang test, I always have this problem at about 35ยฐ. Does anyone have a suggestion what could be causing it?
- Slicer: Orca
- Layer height: 0.2mm
- Infill: 0% (this has improved it a lot, I think the infill was causing bulging)
- Outer walls: 2
- Overhang speed: 10 or 20mm/s (both look the same)
Solution: I mistakenly thought overhang speed in Orca was based on overhang angle, it is percentage instead (which makes much more sense for different layer heights). My 10-25% overhang speed wasn't set to slow down and that must translate to about 35ยฐ at 0.2mm layer height. I now have it set to 30mm/s and it now looks great ๐ And sorry, I was wrong when I stated the overhang speed ๐
Can anyone suggest what causes these lines across the page?
Is a new toner cartridge likely to fix this?
Edit: Line separation is 62.5mm
Edit 2: Thank you to everyone who replied. I've ordered a new toner cartridge and will update this if that solves the problem ๐ซก
Final update: A new toner cartridge fixed it. It's now printing perfectly! Thank you.
view more: next โบ
Thanks. I'm still learning how Lemmy works ๐