this post was submitted on 18 Oct 2023
109 points (88.1% liked)
Linux
48074 readers
930 users here now
From Wikipedia, the free encyclopedia
Linux is a family of open source Unix-like operating systems based on the Linux kernel, an operating system kernel first released on September 17, 1991 by Linus Torvalds. Linux is typically packaged in a Linux distribution (or distro for short).
Distributions include the Linux kernel and supporting system software and libraries, many of which are provided by the GNU Project. Many Linux distributions use the word "Linux" in their name, but the Free Software Foundation uses the name GNU/Linux to emphasize the importance of GNU software, causing some controversy.
Rules
- Posts must be relevant to operating systems running the Linux kernel. GNU/Linux or otherwise.
- No misinformation
- No NSFW content
- No hate speech, bigotry, etc
Related Communities
Community icon by Alpár-Etele Méder, licensed under CC BY 3.0
founded 5 years ago
MODERATORS
you are viewing a single comment's thread
view the rest of the comments
view the rest of the comments
Since you mentioned high cpu temps, do you have a water cooler? It’s possible that the pump is running at a reduced speed or not at all. If it was functioning fine on windows that leads me to believe that it’s not hardware related like some are suggesting.
I do have a AIO radiator. The pump itself is plugged into CHA_FAN1 and shows about 1600RPM, but I don't remember the normal speeds
Are your AIO fans, pump, etc. connected to the motherboard or through a USB hub?
OP this comment could be a major clue to whats happening with your AIO.
I have some fans connected via hub, but the pump and aio fan are connexted directly to the motherboard
That would be where I'd look first. A lot of AIO manufacturers only write drivers for Windows. There's an old Reddit thread that has a few things to try. If this is your first dip into Linux get used to googling things. A lot of things. Ubuntu or Kebuntu are great OS to start on because there is always a forum post or a Reddit thread that deals with exactly what you're dealing with. Once you are more comfortable I'd move onto Linux Mint or straight Debian. All those nice things that make Ubuntu easy to learn will eventually also hold you back.
If your AIO pump came with a hub you likely need to use it instead of plugging directly into the Mobo.
As an example my corsair AIO came with a hub and i didnt want to use it. Finished my build and found out i absolutely had to use it in order for the device to work properly.
Do you know what model AiO you have? Some models report pump speeds as higher since they have multiple magnets triggering the RPM sensor, so the 1600 might actually be 800 or even 400, which is way too low for the pump.
I would try setting the pump (and AiO fan) to 100% speed in the Bios for testing. Some pumps work well with a fan curve, some don't.
Edit with more technical details: Normally each revolution should generate 2 Pulses on the rpm Feedback wire. But Pumps don't always follow this spec so might over or underreport their actual rpm.
Look up CoolerControl I use it for my Corsair AIO, and my CPU cooler runs entirely off a USB header. But CoolerControl also supports motherboard headers.
You can use it to make custom fan curves and check pump/fan speeds.
Check your motherboards manual, there may be a water cooling pump specific header.
AIOs typically pretend to be a fan and you would only need to use that with a custom loop.
I've had similar problems in the past with an AIO, the pump should always be at 100%, so I usually do this through BIOS. My old Mobo had a dedicated pump pin, but the new one doesn't, so I put it on a fan one and configured it to 100% all times. If the pump is not at maximum it might not move enough water for the system to cool.
The problem here might be a difference between how Windows and Linux handle fan control, CHA_FAN1 is a chassis fan, it might be that Kubuntu is not using the CPU temp for it, instead relying on another sensor.
Although to be honest I don't think this might be causing your issue. I'm leaning more to thinking this is related to either the snaps or some problem with the disk you have Linux on. My recommendation is to test a live iso for different distros, if the live iso for Kubuntu works better than on the disk it might imply some issue with the disk, if it's also slow it might be a problem with Kubuntu, I would recommend then testing different distros with KDE Plasma, they would look and feel the same but might be faster if the problem is Ubuntu's snaps. I personally don't like it but I've heard people speak highly of Fedora and OpenSuse.
I've had a few issues with fan control on AMD hardware. In your motherboards BIOS, try taking all fan control off auto, and set it for full load. In your OS, download Radeon-Control (AMD GPU Fan control) and set it for full load. See if your Temps stay high. I think Kubuntu comes with Fan-GUI (I think that's what it's called). Disable it.