flashlight

thanks for following up ;-)

No, I do not yet know the correct command line syntax

I would welcome any help.. here is the backstory:

I bought Hank’s programmer and am trying to learn how to ping the D2…

I dont have an Android phone, and cannot use avrdude on my iMac. I use pymcuprog and issue commands through Terminal in my iMac, to reflash Anduril on my Wurkkos TS10 successfuly.

when I use the gchart programmers for my TS10, I use this command line, that works very well:

pymcuprog ping -t uart -u /dev/tty.wchusbserial1430 -d attiny1616

Im trying to figure out what command line to use for the Emisar D2? 
I think it uses a 1634 chip? I believe I need this info to edit the command line where it says attiny1616. Is that true, or does the D2 use attiny1616?

when I plug the Hank programmer into my iMac, with the pogo pins connected to the head of my D2, and I run this command in Terminal:

**
ls /dev/{tty,cu}.***

the response is

**
tty.Bluetooth-Incoming-Port**

I believe I need that info to tell pymcuprog to use the Hank programmer..

so I took a couple of guesses and modified the command line to ping the D2 like this:

pymcuprog ping -t uart -u /dev/tty.Bluetooth-Incoming-Port -d attiny1634

but that command line does not work in Terminal (yet), I get this response in Terminal:

Unable to setup stack for device attiny1634
Currently supported devices (in ‘devices’ folder):
atmega1608, atmega1609, atmega3208, atmega3209, atmega328p, atmega4808, atmega4809, atmega808, atmega809, atsamd21e18a, atsamd21g18a, attiny1604, attiny1606, attiny1607, attiny1614, attiny1616, attiny1617, attiny1624, attiny1626, attiny1627, attiny202, attiny204, attiny212, attiny214, attiny3216, attiny3217, attiny3224, attiny3226, attiny3227, attiny402, attiny404, attiny406, attiny412, attiny414, attiny416, attiny417, attiny424, attiny426, attiny427, attiny804, attiny806, attiny807, attiny814, attiny816, attiny817, attiny824, attiny826, attiny827, attiny84a, avr128da28, avr128da32, avr128da48, avr128da64, avr128db28, avr128db32, avr128db48, avr128db64, avr16dd14, avr16dd20, avr16dd28, avr16dd32, avr16ea28, avr16ea32, avr16ea48, avr32da28, avr32da32, avr32da48, avr32db28, avr32db32, avr32db48, avr32dd14, avr32dd20, avr32dd28, avr32dd32, avr32ea28, avr32ea32, avr32ea48, avr64da28, avr64da32, avr64da48, avr64da64, avr64db28, avr64db32, avr64db48, avr64db64, avr64dd14, avr64dd20, avr64dd28, avr64dd32, avr64ea28, avr64ea32, avr64ea48, avr8ea28, avr8ea32, pic16f15244, pic16f15276, pic16f15376, pic16f17146, pic16f1768, pic16f1769, pic16f1779, pic16f18146, pic16f18446, pic16f18456, pic16lf18456, pic18f16q40, pic18f16q41, pic18f47k40, pic18f47k42, pic18f47q10, pic18f47q43, pic18f57q43, pic18f57q84, pic24fj128ga705, pic24fj64gu205, uc3a3256

(apparently my pymcuprog install does not include attiny1634)

Do you have any suggestions what the correct command line would be, to ping my Emisar D2?

Once I get that sorted, I will have the Option to also reflash to newer firmware, but that is not my priority. I just want to backup my existing firmware with my eeprom settings.

I dont really want to update to newer D2 firmware, that uses 3C for channel switching. I can switch channels on my D2 using 3H, and I like it that way.

It means I dont have to relearn a different command for my D2, when I want to switch from smooth to stepped ramping. This keeps 3C consistent with my other Anduril lights.