this post was submitted on 02 Apr 2024

25 points (96.3% liked)

homelab

6612 readers

1 users here now

founded 4 years ago

MODERATORS

[email protected]

3D Printer projects for a homelab (programming.dev)

submitted 7 months ago by [email protected] to c/[email protected]

12 comments fedilink hide all child comments

hey,

I'm getting a 3D printer soon. Its on it way right now actually. I was wondering if anyone here has a 3D printer projects that are useful for a Homelab. Hard drive caddies are the only thing I can think of, that would be useful in the homelab. Of course I'm going to use it for other non homelab projects. So ideas would be highly appreciated! Thank you!

top 12 comments

sorted by: hot top controversial new old

[–] [email protected] 10 points 7 months ago

Rack mounting non-rack-mount gear always seemed like an interesting application to me. Raspberry pis, tiny lenovos, network gear, etc.

e.g. https://www.thingiverse.com/thing:4769452

[–] [email protected] 9 points 7 months ago* (last edited 7 months ago) (1 children)

Not home lab specific, but a few things around my house to help inspire you.

Cable fingers

Nuc wall mount

Tool peg board mounts

Heavy ass speaker onto a vesa pole mount to get them above my monitors

Couch gaming gear

Sonos wall mount

[–] [email protected] 8 points 7 months ago

Been a few years so I don't have the link, but I bet you can find this (or something similar) online. If all else fails, I hoard all the files I used somewhere on my nas.

[–] [email protected] 7 points 7 months ago

One of my friends printed this tiny rack for a small switch and two micro PCs. It's pretty cute and nifty

[–] [email protected] 3 points 7 months ago

Rack-mounted beer holder.

Jk. But really, anything which helps organize stuff is a worthwhile job for a 3d printer. Even something to loop fibre optic cables on, so that they don't exceed their maximum bend radii, is useful.

I think you'll also find the 3d printer aids in other endeavors. I've used mine to print replacement car trims, ham radio accessories, a photo film spooler, a bushing to convert vacuum hose diameters, and other odds and ends.

[–] [email protected] 2 points 7 months ago (1 children)

This is very multipurpose, but if you haven't heard of gridfinity, there might be modules that would be helpful you home lab, or your home in general.

[–] [email protected] 1 points 7 months ago

Here is an alternative Piped link(s):

gridfinity

Piped is a privacy-respecting open-source alternative frontend to YouTube.

I'm open-source; check me out at GitHub.

[–] [email protected] 2 points 7 months ago

I have a 10" width rack cabinet where my Proxmox cluster (three mini Lenovo Thinkcentre) lives. I'm currently designing a 10" mount to hold an old phone so that I can see my server monitoring/status through the glass of the door.

3D printing is great for stuff like that.

[–] [email protected] 1 points 7 months ago

Special cable trays for your specific setup? Opencompute's rack parts?

[–] [email protected] 1 points 7 months ago

Cable management, you don't't want any heavy rackmount stuff 3d printed.

I did a nice fanmount for my Arris NTD, i've also done some toggles to go with paracord to loop up network cabling. Thangs, cults3d and thingiverse are your friends :)

[–] [email protected] 1 points 7 months ago

I haven't done it yet, but custom case for repurposed hardware. Mine is a mini PC I acquired free after the m2 drive died. I got an m2 to 6 sata adapter board and it already had an unused SATA port so I'm planning on doing SATA SSD boot with 6x nas drives and print an alternate case for it. Actually powering the drives is the part I'm least sure about.