Welcome to R/3D Printing! Come for the Benchy, stay for the Calibration!

The original post: /r/3dprinting by /u/epicly69 on 2024-12-27 11:49:40.

I recently got given a mankati fullacale Xt printer but the nozzle is cactus. It's 0.4mm and uses 3mm filament and screws onto the extruder with m6 thread. The heating element attaches to the smooth part of the nozzle. I can't find any replacements online since mankati got bought out by another company, is there anywhere I can get a replacement, or alternatively is there a nozzle from another printer I can use?

The original post: /r/3dprinting by /u/Amusedto on 2024-12-27 11:22:23.

Idk if this is my Printer or its Cura g.code issue but I've always noticed this excessive travel with any print and It starts to print then go back to the corner print again and then do the same thing for each little print this has honestly ruined a lot of prints i have made because the way it accelerates itll make the extruder belt or motor like get stuck then it skip and then be off track to the print and start printing unaligned. With this too ive also thought about how much print time over the last like 2 years ive wasted on print time But i then figured out what it was and it doesnt make any sense to me that the extra travel MAKES IT FASTER then when its turned OFF it takes almost an hour how does this make sense and ive always noticed it with almost every print as you can see in the video it prints out fine then it all of a sudden happens and then if you watch to the end itll even switch sides of ends at which it like returns too then prints a small part and then back to X location so if i keep the setting on itll take an hour less but risks ruining the print but if on then i waste an hour on what seems to be just a error because it uses the same value and weight not evil .00 of a decimal changes i just dont understand

THIS IS HAPPENS WHEH I TURN OFF COMBING

With it turned Off 3 HOURS

With it turned on 2 Hours Like how

https://reddit.com/link/1hmlj14/video/evdp50n4269e1/player

FYI I DID SPEED UP AND SLOW DOWN THE VIDEO

The original post: /r/3dprinting by /u/krzakpl on 2024-12-27 11:17:06.

The original post: /r/3dprinting by /u/gamertuts on 2024-12-27 11:14:41.

The original post: /r/3dprinting by /u/marshmellobacon on 2024-12-27 04:47:50.

The original post: /r/3dprinting by /u/Ok-Drink750 on 2024-12-26 22:27:08.

The original post: /r/3dprinting by /u/TomTomXD1234 on 2024-12-26 20:52:43.

The original post: /r/3dprinting by /u/KingJM27 on 2024-12-26 20:22:56.

The original post: /r/3dprinting by /u/AudienceLumpy6580 on 2024-12-26 19:49:23.

The original post: /r/3dprinting by /u/Amphisbaena1 on 2024-12-26 19:00:25.

The original post: /r/3dprinting by /u/Specialist-Curve-444 on 2024-12-26 18:25:15.

The original post: /r/3dprinting by /u/ericthepoolboy on 2024-12-26 18:06:23.

The original post: /r/3dprinting by /u/FlavorBlastedCheerio on 2024-12-26 17:32:16.

The original post: /r/3dprinting by /u/Ubernero on 2024-12-26 16:45:44.

The original post: /r/3dprinting by /u/hasty1996 on 2024-12-26 16:33:24.

The original post: /r/3dprinting by /u/Striking-Gas1118 on 2024-12-26 14:28:15.

The original post: /r/3dprinting by /u/Alagor9 on 2024-12-26 13:29:40.

The original post: /r/3dprinting by /u/NIDNHU on 2024-12-26 11:25:34.

The original post: /r/3dprinting by /u/Thelinkr on 2024-12-26 10:17:13.

The original post: /r/3dprinting by /u/Martin_au on 2024-12-26 23:51:34.

Just curious if anyone else is seeing this. Comparison between Makeronline and Makerworld and Printables. All three sites have the same model collection.

MakerOnline for the last couple of months.

Printables. A bit of an early surge because I did a bunch of useful models in October, but consistent baseline.

Makerworld. Nice and consistent behaviour.

The original post: /r/3dprinting by /u/Empty_Sandwich_6884 on 2024-12-26 23:48:17.

The original post: /r/3dprinting by /u/Difficult-Blood170 on 2024-12-26 23:46:47.

Hello all, I have a ender 3 v3 se right now and I’m looking to upgrade particularly to a bambulab. I want to see what you guys think I should get. I like high quality prints and I will be using ams or the type of multicolor printing that it supports . I mostly want it to be enclosed but it is fine if it isn’t. I want it to be stress free unlike my other printer (auto leveling, good first layer, not failing halfway through, etc)

The original post: /r/3dprinting by /u/QueenShiroi on 2024-12-26 23:42:31.

The original post: /r/3dprinting by /u/Whole-Basil-9784 on 2024-12-26 23:38:48.

Did you notice any resudue in the room where you print ABS ? I mean on the cucurtains, walls, windows ... In other words can you trash the place if you pront ABS a lot?

The original post: /r/3dprinting by /u/RomaTul on 2024-12-26 23:38:29.